A-Plus Paints | Paint Products Manufacturers and Suppliers in Philippines

A-Plus Floor Shield® High-Build 2k Polyurethane Parking Floor Coating is a two-component solvent-based polyurethane floor coating known for its superior durability and extreme abrasion and chemical resistance. It is easy to apply and cures fast to a non-slip glossy film that can withstand abrasion, water, chemicals, and UV exposure. It is the choice of paint best used for parking flooring where frequent exposure to chemicals and high friction occurs.

☑ Two-Component, Polyurethane-Based Coating
☑ Easy-To-Apply, Non-Slip, Fast Drying
☑ Superior Resistance to Alkali, UV Exposure, Chemicals, and Weathering
☑ Excellent Abrasion and Chemical Resistance
☑ High Gloss, Easy to Maintain, Waterproof
☑ For Interior and Exterior Use
☑ Ideal for Parkings, Industrial Plants, Warehouses, and many more

Category: Floor Coatings Tag: Polyurethane Parking Floor Coating

Specifications

Principal Uses: Ideal for heavy foot traffic and highly exposed areas such as parking and open spaces, industrial plants, warehouses, traffic markings, and many more.

Sheen: Gloss

Coverage: 20-25 sqm per gallon

Surface Dry: 6-8 hours

Recoat Interval: 6-8 hours

Dry Through: Overnight curing time for light traffic

Thinning: Up to 10% A-Plus® PG Urethane Thinner

Clean-up Solvent: Up to 10% A-Plus® PG Urethane Thinner

Application: Brush, Roller, or Spray

Packaging: 4L

Pot life: 2-3 hours at room temperature

Surface Preparation & Precautions

For Concrete Surfaces:

1. Ensure proper surface preparation by removing any oil and dirt by detergent cleaning.
2. Sand or use a mechanical floor grinder with large grit to roughen and level the surface, allowing the paint enhanced grip and adhesion.
3. Surface must be completely dry and clean before application of paint.
4. To repair large concrete surface imperfections, use either of the following:

– A-Plus Procrete® Low Viscosity Construction Epoxy – used for patching medium-sized concrete imperfections covering a large area.
– A-Plus Procrete® High Viscosity Construction Epoxy – used for patching larger-sized concrete imperfections covering smaller areas.

5. If previously painted, strip off all paint to bare substrate with A-Plus Supertanggal® Paint Remover.
6. MIX WELL BEFORE USING.

For Metal Surfaces:

1. Remove dust, dirt, grease, oil, wax and other foreign matter by sanding and using a rag soaked in paint thinner.
2. For repainting, use A-Plus Supertanggal® Paint Remover to strip off old paint film to bare substrate then remove oil and grease by solvent cleaning followed by scuff sanding. To remove rust, wire brush or strip affected areas while applying A-Plus® Rust Converter. Let it sit for 10 – 15 minutes before washing off the surface thoroughly with water, letting it dry before applying paint.
3. Primer should be applied immediately upon drying of the surface before rust sets in.

Painting Procedure

Mixing Direction:

Stir and shake both components separately before mixing together.
Slowly add the hardener to the paint and mix slowly and thoroughly for 5-10 minutes before application.
For better mixing, transfer both components to a larger container.
Apply paint within the pot life time limit to prevent premature curing.

Application Over Steel Floors:

Sealer: Apply 1 coat of A-Plus Floor Guard® Concrete Sealer. Allow to cure for at least 6 hours before next step.
Topcoat: Apply 2-3 coats of A-Plus Floor Shield® High-Build 2k Polyurethane Parking Floor Coating.
Allow the surface to cure overnight before subjecting to light traffic. Allow the surface to cure for at least 3-7 days before subjecting to heavy traffic.

Application Over Concrete Floors (Plain Finish Without Aggregates):

Sealer: Apply 1 coat of A-Plus Floor Guard® Concrete Sealer using a short nap roller or paint brush. Allow to cure for at least 6 hours before the next step.
Topcoat: Apply 2-3 coats of A-Plus Floor Shield® High-Build 2k Polyurethane Parking Floor Coating.
Allow the surface to cure overnight before subjecting to light traffic. Allow the surface to cure for at least 3-7 days before subjecting to heavy traffic.

Application Over Concrete Floors (Non-Skid Finish With Broadcast Aggregates):

Sealer: Apply 1 coat of A-Plus Floor Guard® Concrete Sealer using a short nap roller or paint brush. On the still wet A-Plus Floor Guard® Concrete Sealer, broadcast aggregates at 1kg per sqm. Allow to cure for at least 6 hours before the next step.
Topcoat: Apply 2-3 coats of A-Plus Floor Shield® High-Build 2k Polyurethane Parking Floor Coating.
Allow the surface to cure overnight before subjecting to light traffic. Allow the surface to cure for at least 3-7 days before subjecting to heavy traffic.

Specifications